ToolGuyd

Tool Reviews, New Tool Previews, Best Tool Guides, Tool Deals, and More!

  • New Tools
  • Reviews
  • Guides
    • Best Cordless Power Tool Brand
    • Tool Brands: Who Owns What?
    • Best Cordless Drills (2021)
    • Dewalt UWO Explained
    • Where to Buy Tools
    • Best Tool Kit Upgrades
    • Best Extension Cord Size
    • Best Tape Measure
    • Best Safety Gear
    • Best Precision Screwdrivers
    • Best Tool Brands in Every Category
    • Ultimate Tool Gift Guide
    • More Buying Guides
  • Hand Tools
    • Bit Holders & Drivers
    • EDC, Pocket, & Multitools
    • Electrical Tools
    • Flashlights & Worklights
    • Knives
    • Mechanics’ Tools
    • Pliers
    • Screwdrivers
    • Sockets & Drive Tools
    • Wrenches
    • All Hand Tools
  • Power Tools
    • Accessories
    • Cordless
    • Drills & Drivers
    • Oscillating Tools
    • Saws
    • Woodworking Tools
    • All Power Tools
  • Brands
    • Bosch
    • Dewalt
    • Makita
    • Milwaukee
    • Ryobi
    • All Brands
  • USA-Made
  • Deals
ToolGuyd > Hand Tools > Mechanics' Tools > Friendly Reminder: Don’t Use a Jack Without Jack Stands

Friendly Reminder: Don’t Use a Jack Without Jack Stands

Apr 1, 2013 Stuart 7 Comments

If you buy something through our links, ToolGuyd might earn an affiliate commission.

Craftsman Professional 4-Ton Jack Stands

This is a friendly reminder that, when using a car jack you should always use jack stands as well. Chocking the wheels is also a good idea.

Seriously, use jack stands. People have been crushed and killed by their vehicles.

Advertisement

Most jacks are designed to be used to lift a vehicle high enough so that jack stands can be placed at support locations.

The only exception would be if you’re changing a flat on the side of the road with the emergency scissor jack that came with your vehicle. Even then, work on level and hard ground, don’t stick your body under any part of the car, chock the opposite wheels if you can, follow the instructions to the letter, and use common sense.

Even the best automotive jacks in the world can fail. A falling car can be fatal if not severely damaging to someone working beneath it. Cars can also roll or shift position, even with the parking brake engaged.

So don’t try to save money, time, or effort by working without jack stands. They don’t even cost that much to begin with – you can get a pair of 2-ton stands starting at about $25.

Here’s what I would buy:

Craftsman 4-Ton Jack Stands(via Sears)
Craftsamn 3-Ton Stands(via Sears)

Advertisement

When buying jack stands, remember to buy stands with higher load ratings than your vehicle’s weight. Also keep in mind that stands can have different height ranges.

Jack Stands(via Amazon)
Wheel Chocks(via Amazon)

Reader Tips:

Jeff commented about how cheaper stands that don’t have flat gussets or feet can sink into asphalt and softer materials.

Jerry mentioned about how some jack stands have notches sized for 2×6 or 2×8 lumber. That way, the stands will dig into the wood rather than asphalt or soft flooring.

Related posts:

No related posts.

Sections: Editorial, Mechanics' Tools, Shop Essentials Tags: jack standsMore from: Craftsman

« Ergodyne Arsenal Tool Bags, 50%-off Sale
Bovidix, a Russian Professional-Grade Mechanics Tool Brand »

7 Comments

  1. Mati

    Apr 1, 2013

    So Stuart, is this where the phrase “that is jacked up” came from?

    Just kidding, but seriously people, safety is quite important, especially when dealing with cars. I’ve seen several car accidents in my lifetime and some were quite horrid.

    Reply
    • Stuart

      Apr 1, 2013

      Technically, jack means to raise, hoist, lift, etc. “Jacked up” can be traced directly to the definition, depending on context.

      Reply
  2. jeff_williams

    Apr 1, 2013

    Most cheap jack stands are still quite dangerous on asphalt. They really should be set on steel plate. The ones pictured have small gussets in the corner so that they don’t cut right through the tar.

    Reply
    • Jerry

      Apr 1, 2013

      Many also have a wide flat notch at the bottom, such as the ones pictured so you can set a 2×6 or 2×8 (or even 2×10 on some bigger stands) under them in soft surfaces, or ones you do not want damaged. Use a board as wide as will fit the notch, for safety.

      Reply
  3. Stuart

    Apr 2, 2013

    Those are both very good points, and I have edited them into the post accordingly.

    Reply
  4. Dan

    Apr 2, 2013

    Relevant post Stu, a local guy just died as a result of working on a car jacked up with a (gulp) forklift hooked under wheel wells. Sad, but you have to wonder about the thought process here.

    Reply
  5. Joe

    Apr 5, 2013

    I will admit that I don’t bother with jack stands when I am changing out my wheels (summer/snow), I just jack up that part of the car, pull off the wheel, put the new one on, and let it down.

    Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

  • Email
  • Facebook
  • Instagram
  • YouTube

Newsletter

Sign up to receive the latest tool news.

Recent Comments

  • Matt_T on I Need to Vent About My Precision Matthews Mill: “Guessing it’s the right hand bearing that’s stuck? If so tap it back down against the spacer then check for…”
  • Stuart on New Craftsman Cordless Screwdriver Comes with a USB Dock: “It’s not guaranteed to launch at Amazon. You might find it sooner at Lowe’s.”
  • Oleg K on New Craftsman Cordless Screwdriver Comes with a USB Dock: “I’ll just wait until it’s available on Amazon instead of paying AcmeTools’ shipping fee. Will have to replace craftsman’s cheap,…”
  • Oleg K on People are Stumped by the Security Tag on Dewalt Hammers: “Are they also stumped by a poorly-understood yet well-documented phenomenon called “theft”?”
  • Oleg K on New Wiha GoStack – a “Revolutionary” Storage System: “Everything, everybody makes is revolutionary, will “change the way you work”, will “redefine everything” but it always ends up being…”
  • Oleg K on There’s Been a Surge in Fractal Vises: “They start at ~$400 and cost upwards of $5k, who needs them? They’re something I can literally replace with $10…”
ToolGuyd New Tool Reviews Image

New Tool Reviews

Buying Guides

  • Best Cordless Drills
  • Best Euro Hand Tool Brands
  • Best Tool Brands
  • Best Cordless Power Tool Brands
  • Tools for New Parents
  • Ultimate Tool Gift & Upgrade Guide
ToolGuyd Knife Reviews Image

Knife Reviews

ToolGuyd Multi-Tool Reviews Image

Multi-Tool Reviews

ToolGuyd LED Flashlight and Worklight Reviews Image

LED Light Reviews

  • Home
  • About
  • Contact
  • Stores
  • Videos
  • AMZN Deal Finder
  • Privacy Policy
  • Terms of Use
  • Disclosure