While I was at Acme Tool’s fall sale, I was able to quickly demo a few MetaboHPT (formerly known as Hitachi) MultiVolt tools. Several of the tools are now available for sale including the 36V dual-bevel 10″ miter saw shown above.
I wasn’t really able to challenge the power of the miter saw because the only wood they only gave me a 2×4. I did make a few straight cuts and a 45° miter and the saw didn’t even notice it was cutting through the 2×4. That’s a good start anyway.
I also didn’t notice any appreciable sawdust blowing forward at me unlike some other saws I’ve tested. As you can see in the photos, the dust bag definitely wasn’t catching all the sawdust, but then again there aren’t many saws that can collect dust well without a vacuum.
Notice that the rails are in the front of the saw and the motor slides forward, this allows the saw to be placed closer to the wall saving space. You’ll also notice the two thumb wheels right above the blade guard. These are for aligning the laser cut line without tools, although you can’t access them if you pull the handle down because the blade guard gets in the way.
I was also able to try the 36V reciprocating saw. This new saw has a 1-1/4″ stroke length and a dual counter weight system to reduce vibrations transmitted to the user.
To test the saw they had set up a 2×10 in a Jawhorse. While the saw had plenty of power, I felt it vibrated more — not less — than other cordless recip saws I’ve used. When I asked the rep about the vibration, he said that if you compare it side by side with other cordless recip saws it should vibrate less because of the dual counter weight mechanism. I’m not convinced yet.
While I was inside the store, I was able to get some photos of the new MultiVolt AC adapter. It comes in two parts: a big box that the AC cord runs into, and the battery adapter that’s connected by a long cord. The battery adapter is about the size of a 10 cell li-ion-pack.
As you can see above the big box is about 30% longer than the battery adapter, slightly wider, and slightly taller. What surprised me was how light both the battery adapter and the other box were. Their total weight is only 5.5lbs. I was expecting one of them to weigh significantly more because of the size of the transformer they’d need to use to get the rated 2000W output.
Talking more about output, 2000W is a little over what you can get from a regular 15A 120V circuit. The maximum number of watts you can draw should only be 1800W. I’m not exactly sure how they are specifying 2000W.
What’s Available Now
All of the MultiVolt tools are brushless, and the prices listed below are for the bare tool.
- 4/8Ah 18/36V MultiVolt battery $100
- MultiVolt Starter kit with battery and charger $150
- 36V AC adpater $150
- 36V 1/2″ hammer drill $359
- 36V triple hammer impact driver $379
- 36V 7-1/4″ circular saw $359
- 36V 10″ dual bevel sliding miter saw $619
- 36V recip saw $399
- 36V 1-9/16″ SDS Max rotary hammer $749
- 36V 4-1/2″ grinders (slide and paddle switch models) $359
- 36V 1/2″ hog ring impact wrench $449
- 36V 3/4″ hog ring impact wrench $499
Several of the tools are already in stock at Acme Tools and others are arriving soon. I’ve even see a Metabo HPT display at Menards with the starter kit, circular saw, impact, drill, and recip saw.
Acme does have a deal going where you buy one of the MetaboHPT bare tools and you can either get a free starter kit or 36V AC adapter. It works both in stores and online, but they say the deal is only good until supplies last.
To redeem the deal online, you just add the bare tool to your shopping cart. When you go into your shopping cart, you’ll see a button below your tool that says”select your free gift.”
Buy Now (via Acme Tools)
The next big tool in the MultiVolt platform is the 36V table saw. It’s supposed to be based on the C10RJ 10″ jobsite table saw they currently sell. Supposedly it’s due out early next year.